引用本文:李豪,吴凤和,赵夙,张庆龙,李一飞.超声波冲击技术对AA6061-T6空蚀行为的影响∗[J].中国表面工程,2021,34(3):83~89
Li Hao,Wu Fenghe,Zhao Su,Zhang Qinglong,Li Yifei.Effects of Ultrasonic Impact Technology on Cavitation Erosion Behavior of AA6061-T6[J].China Surface Engineering,2021,34(3):83~89
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【EndNote】   【RefMan】   【BibTex】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被：浏览 1832次   下载 680次 本文二维码信息
码上扫一扫！
分享到： 微信 更多
字体:加大+|默认|缩小-
超声波冲击技术对AA6061-T6空蚀行为的影响∗
李豪1,2, 吴凤和1, 赵夙2, 张庆龙2, 李一飞2
1.燕山大学机械工程学院 秦皇岛 066004;2.中国科学院宁波材料技术与工程研究所 宁波 315201
摘要:
AA6061-T6 铝合金因较高的比强度、良好的可成型性广泛应用于汽车工业中,但较差的空蚀性能极大的降低了其使用寿命。 利用超声波冲击技术在 AA6061-T6 表面制备了塑性形变强化层,研究塑性形变强化层的微观组织、残余应力及显微硬度分布和抗空蚀性能。 结果表明,超声波冲击强化后铝合金表面择优取向由原始的(200)转变为(111),并形成约 140 μm 塑性变形层。 与未强化试样相比,强化试样表面显微硬度提高了 80. 7%,并形成 140 μm 硬化层;表面植入残余压应力达到 -259 MPa,残余压应力层深达到 700 μm。 超声波冲击强化处理后的空蚀性能提高 2. 36 倍;空蚀表面形貌分析表明强化后试样空蚀机制由韧性断裂转变为脆性断裂和疲劳破坏。 研究表明超声波冲击强化后试样表面晶粒细化、择优取向转变、硬度提高以及较高残余压应力等增强了材料的抗空蚀性能。
关键词:  AA6061-T6  超声波冲击技术  空蚀  微观结构  力学性能
DOI：10.11933/j.issn.1007-9289.20210114002
分类号:TG172
基金项目:航空科学基金(20184599001)、宁波市“3315”创新团队(Y80929DL04)和宁波市科技创新 2025 重大专项(2018B10059) 资助项目
Effects of Ultrasonic Impact Technology on Cavitation Erosion Behavior of AA6061-T6
Li Hao1,2, Wu Fenghe1, Zhao Su2, Zhang Qinglong2, Li Yifei2
1.College of Mechanical Engineering, Yanshan University, Qinhuangdao 066004 , China;2.Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 , China
Abstract:
AA6061-T6 aluminum alloy is widely used in the automobile industry due to its high specific strength and good formability, but its poor cavitation corrosion performance greatly decreases its service life. A plastic deformation layer was prepared by ultrasonic impact technology( UIT). The microstructure, residual stress, micro-hardness distribution and cavitation erosion resistance of the plastic deformation strengthening layer are investigated. Results show that the preferred orientation of the aluminum alloy surface changed from (200) to (111) after UIT, and a 140 μm plastic deformation layer was formed. The surface micro-hardness of UIT sample increased about 80. 7% and formed a 140 μm hardened layer . The surface residual stress of UIT sample was -259 MPa, and the depth of the residual compressive stress layer reached 700 μm. The cavitation erosion performance after UIT is increased by 2. 36 times. The analysis of cavitation surface morphology shows that cavitation erosion mechanism of UIT sample changes from ductile fracture to brittle fracture and fatigue failure. Research have proved that the surface grain refinement, preferred orientation transformation,micro-hardness increase and higher residual compressive stress of UIT samples enhance cavitation resistance of the material.
Key words:  AA6061-T6  ultrasonic impact technology  cavitation erosion  microstructure  mechanical property
手机扫一扫看