| 引用本文: | 李晖， 陈亚茹， 邓书彬， 梁举科.60Si2Mn钢高速电弧喷涂耐磨涂层的摩擦磨损性能[J].中国表面工程,2015,28(4):77~83 |
| LI Hui, CHEN Yaru, DENG Shubin, LIANG Juke.Friction-wear Behavior of 60Si2Mn Steel Sprayed with Wear-resistance Coating by High Velocity Arc Spraying[J].China Surface Engineering,2015,28(4):77~83 |
|
| 摘要: |
| 为提高旋耕刀的耐磨性并延长其使用寿命，利用高速电弧喷涂技术在旋耕刀材料60Si2Mn钢表面制备NiAl粘结层与NiAl2O3、Cr2O3、SiC、Cr、Ti和Fe构成的耐磨涂层。经XRD、显微组织分析及硬度测试得到，耐磨涂层由Fe9.64Ti0.36、FeAl、Al2O3和SiO2多相组成，组织均匀致密，表面硬度达到1 037 HV0.2，比传统淬火、中温回火的表面硬度提高69%，表层硬度最高达到1 202 HV0.2。摩擦磨损试验结果表明，耐磨涂层与传统淬火、中温回火相比，体积磨损量下降60%，摩擦因数降低44%，电弧喷涂涂层有效的降低了摩擦和磨损，改善了材料的耐磨性。 |
| 关键词: 旋耕刀 高速电弧喷涂 耐磨涂层 摩擦磨损 |
| DOI：10.11933/j.issn.1007-9289.2015.04.010 |
| 分类号: |
| 基金项目: |
|
| Friction-wear Behavior of 60Si2Mn Steel Sprayed with Wear-resistance Coating by High Velocity Arc Spraying |
|
LI Hui, CHEN Yaru, DENG Shubin, LIANG Juke
|
|
a. College of Materials Science and Engineering， b. College of Mechanical Engineering， Chongqing University of Technology
|
| Abstract: |
| To improve the wear resistance and prolong its life of rotary tiller blades, this paper involved spraying NiAl bond coating and ceramic wearresistance coating made up of NiAl2O3, Cr2O3, SiC, Cr, Ti, and Fe by high velocity arc spraying on the surface of 60Si2Mn that was usually used in rotary tiller blades. XRD analysis indicates that the wear resistant coating is a multiphase structure consisting of Fe9.64Ti0.36, Al2O3, FeAl and SiO2 and microstructure of the coating is uniform and compact. Hardness test results show that the surface hardness of wear resistant coatings is 1 037 HV0.2, which is 69% higher than that of the quenching and medium temperature tempering sample, and the maximum hardness of the gradient layer is 1 202 HV0.2. Friction and wear test results show that the volume wear of wear resistant coating compared with the quenching treatment sample is reduced by approximately 60% and the reduction friction coefficient of wear resistant coating is 44%, which illustrates that wear resistant coatings prepared by arc spraying can effectively reduce the degree of friction and wear, thus improving the wear resistance. |
| Key words: rotary tiller blades high velocity arc spraying wearresistance coating friction and wear |
