引用本文:韩国峰， 朱胜， 王晓明， 王之千.5083铝合金表面钛铝基耐蚀涂层与TA2钛合金接触腐蚀[J].中国表面工程,2014,27(6):44~49
HAN Guofeng, ZHU Sheng, WANG Xiaoming, WANG Zhiqian.Galvanic Corrosion Between TiAlBased Corrosionresistance Coating on 5083 Aluminum Alloy and TA2 Titanium Alloy[J].China Surface Engineering,2014,27(6):44~49
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【EndNote】   【RefMan】   【BibTex】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被：浏览 4122次   下载 2948次 本文二维码信息
码上扫一扫！
分享到： 微信 更多
字体:加大+|默认|缩小-
5083铝合金表面钛铝基耐蚀涂层与TA2钛合金接触腐蚀
韩国峰， 朱胜， 王晓明， 王之千
装甲兵工程学院 再制造技术重点实验室， 北京 100072
摘要:
针对5083铝合金与TA2钛合金接触腐蚀问题，采用超音速微粒沉积技术在5083铝合金表面制备Ti45Al7Nb4Cr耐蚀涂层，采用扫描电子显微镜（SEM）和能谱仪（EDS）对涂层截面和与基体界面进行测试，分析涂层孔隙率和与5083铝合金基体的结合机制；采用电化学工作站测试5083铝合金、TA2钛合金、TiAl合金铸锭和涂层的极化曲线，并对比研究5083铝合金、TiAl合金铸锭和涂层与TA2钛合金接触腐蚀敏感性。结果表明：涂层孔隙率为1.4%，涂层与基体结合机制为机械结合，通过在5083铝合金表面制备Ti45Al7Nb4Cr合金防护涂层后，可使材料电极电位由-913.90 mV升高到-572.47 mV，与TA2钛合金的接触腐蚀电流密度由16.2 μA/cm2降为0.21 μA/cm2，接触腐蚀敏感性由E级降到A级，解决了铝合金与钛合金的接触腐蚀防护问题。
关键词:  5083铝合金  TA2钛合金  TiAl涂层  接触腐蚀
DOI：10.11933/j.issn.1007-9289.2014.06.004
分类号:
基金项目:
Galvanic Corrosion Between TiAlBased Corrosionresistance Coating on 5083 Aluminum Alloy and TA2 Titanium Alloy
HAN Guofeng, ZHU Sheng, WANG Xiaoming, WANG Zhiqian
Science and Technology on Remanufacturing Laboratory, Academy of Armored Forces Engineering, Beijing 100072
Abstract:
To solve the galvanic corrosion problem between 5083 aluminum alloy and TA2 titanium alloy, Ti45Al7Nb4Cr corrosionresistance coating was prepared on 5083 aluminum alloy surface through supersonic particle deposition technology. The coating section and interface morphology were observed to analyze porosity and combining mechanism by scanning electron microscopy (SEM) and energy disperisve spectrometer (EDS). The polarization curves of 5083 aluminum alloy, TA2 titanium, titanium aluminum ingot and coating was tested by electrochemical workstation. The galvanic corrosion sensitivity of TiAl coating and TA2 titanium was studied. The results show that the coating porosity is 1.4%, and the combining mechanism between the coating and the substrate is mechanical bond. The prepared Ti45Al7Nb4Cr corrosion coating on 5083 aluminum alloy surface can make the electrode potential improve from -913.90 mV to -572.47 mV, the galvanic corrosion current between the coating and TA2 titanium decrease from 16.2 μA/cm2 to 0.21 μA/cm2, and the galvanic corrosion sensitivity decrease from E to A. The protection problems of galvanic corrosion between aluminum alloy and titanium alloy are resolved.
Key words:  5083 aluminum alloy  TA2 titanium alloy  TiAl coating  galvanic corrosion
手机扫一扫看