搅拌摩擦加工改性冷喷涂Al-12Si合金涂层的组织和性能

黄春杰; 李文亚; 李锦锋; 余敏; 廖汉林

引用本文:	黄春杰，李文亚，李锦锋，余敏, 廖汉林.搅拌摩擦加工改性冷喷涂Al-12Si合金涂层的组织和性能[J].中国表面工程,2013,26(5):54~58
	HUANG Chunjie, LI Wenya, LI Jinfeng, YU Min, LIAO Hanlin.Microstructure and Properties of Cold Sprayed Al-12Si Alloy Coating Followed by Friction Stir Processing[J].China Surface Engineering,2013,26(5):54~58

【打印本页】【HTML】【下载PDF全文】【查看/发表评论】【EndNote】【RefMan】【BibTex】

←前一篇|后一篇→

过刊浏览高级检索

本文已被：浏览 4493次下载 2870次	码上扫一扫！
分享到：微信更多字体:加大+\|默认\|缩小-
搅拌摩擦加工改性冷喷涂Al-12Si合金涂层的组织和性能
黄春杰，李文亚，李锦锋，余敏, 廖汉林^1,2
1.西北工业大学摩擦焊接陕西省重点实验室, 西安 710072;2.贝尔福蒙贝利亚技术大学, 法国贝尔福 90010

摘要:

采用冷喷涂在碳钢基体上沉积制备了Al12Si合金涂层，分别采用平端面和渐开线端面的无针搅拌头以950 r/min转速对涂层表面进行搅拌摩擦加工(FSP)改性。采用光镜和扫描电镜对喷涂态和FSP改性后涂层的组织结构进行了表征。结果表明：采用两种搅拌头获得了不同形貌的组织，随着渐开线端面搅拌头的移动，提高了热输入，涂层中组织出现了过热造成的气孔缺陷。Si颗粒在FSP的塑性变形过程中得到了充分的混合，均匀地分散在了涂层中，分析表明沉积粒子的再分布和晶粒的细化能显著提高涂层的表面性能，此外，两种FSP搅拌头改性后涂层表面的硬度分别为113.8 HV0.5和125.1 HV0.5。

关键词: 冷喷涂搅拌摩擦加工 Al12Si合金显微组织力学性能

DOI：10.3969/j.issn.1007-9289.2013.05.010

分类号:

基金项目:

Microstructure and Properties of Cold Sprayed Al-12Si Alloy Coating Followed by Friction Stir Processing

HUANG Chunjie, LI Wenya, LI Jinfeng, YU Min, LIAO Hanlin^1,2

1.Shanxi Key Laboratory of Friction Welding Technologies, Northwestern Polytechnical University, Xi’an 710072;2.Université de Technologie de BelfortMontbéliard, Belfort 90010, France

Abstract:

Al12Si alloy coating was deposited onto a mild steel substrate by cold spraying and subsequently modified by friction stir processing (FSP) at a tool rotation speed of 950 r/min using flat and involutes cylinder tools to improve its microstructure and property. The microstructures of the coating after FSP and the ascoldsprayed coating were investigated by optical microscope and scanning electron microscope. The results show that the coating presents different microstructures after two different FSP conditions and pore defects is found in the coating with the involutes cylinder tool because the heat input increases with increasing stirring time. The ascoldsprayed coating contained Si particles at the grain boundaries, and the FSP process could break up and disperse these Si particles more uniformly. It is suggested that the redistribution and grain size refinement of Al12Si particles during FSP could significantly improve the coating performance. The microhardness of the coating modified by the two different tools is 113.8 HV0.5 and 125.1 HV0.5, respectively.

Key words: cold spraying friction stir processing Al12Si alloy microstructure mechanical property