引用本文:高永建1，张世堂1，邓智昌2，宝 民2，周健松3.激光熔覆高温自润滑覆层的摩擦学特性[J].中国表面工程,2011,24(2):51~56
GAO Yong–jian1, ZHANG Shi–tang1, DENG Zhi–chang2, BAO Ming2, ZHOU Jian–song3.Tribological Properties of Laser Cladding High–temperature Self–lubrication Composite Coatings[J].China Surface Engineering,2011,24(2):51~56
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【EndNote】   【RefMan】   【BibTex】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被：浏览 3398次   下载 2624次 本文二维码信息
码上扫一扫！
分享到： 微信 更多
字体:加大+|默认|缩小-
激光熔覆高温自润滑覆层的摩擦学特性
高永建1，张世堂1，邓智昌2，宝 民2，周健松31,2,3
1. 中国人民解放军92117部队，北京 100072;2. 中国人民解放军驻617厂军事代表室，内蒙古 包头 014032;3. 中国科学院兰州化学物理研究所，兰州 730000
摘要:
采用激光熔覆技术制备了Ni3Al–BaF2/CaF2–Ag基高温自润滑耐磨覆层，考察了覆层在不同温度下的摩擦学性能及高温自润滑机理。结果表明，对复合粉末的预先机械合金化处理，改善了覆层组织的相容性及覆层的摩擦学性能。在室温至800 ℃的宽温域范围内，覆层的摩擦因数及磨损率分别在0.30～0.34及(2.6～8)×10-5 mm3/m?N之间波动，覆层表现出较平稳的摩擦磨损性能。在中低温度摩擦时, 磨损形式主要为微断裂及磨粒磨损；在600 ℃及以上温度摩擦时，磨损形式受润滑相的热软化与Ni3Al粘结相的摩擦氧化反应共同作用的控制。
关键词:  激光熔覆  金属基自润滑覆层  摩擦学性能  机理
DOI：
分类号:
基金项目:
Tribological Properties of Laser Cladding High–temperature Self–lubrication Composite Coatings
GAO Yong–jian1, ZHANG Shi–tang1, DENG Zhi–chang2, BAO Ming2, ZHOU Jian–song31,2,3
1. The PLA 92117 Troops, Beijing 100070;2. The PLA Military Representative Office in 617 plants, Baotou Inner Mongolia 014032;3. Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000
Abstract:
The self–lubrication Ni3Al–BaF2/CaF2–Ag metal matrix composite coatings were fabricated on 1Cr18Ni9Ti stainless steel substrates by laser cladding. The friction and wear behavior of the composite coating sliding against Si3N4 ceramic ball from room temperature to 800 ℃ was evaluated using a ball–on–disc friction and wear tester, and worn surface morphologies of the coating were observed using a scanning electron microscopy. It was found that the composition consistent and tribological properties of Ni3Al–BaF2/CaF2–Ag composite coating could be improved pre–milling the composite powders by mechanical alloying. The composite coating has a good friction–reducing and antiwear abilities at elevated temperatures up to 800 ℃. The laser cladding composite coating was dominated by mixed layer detachment and abrasive wear as it slid against the Si3N4 ceramic ball below 600 ℃. With further increase in the test temperature above 600 ℃, it was characterized by softening of BaF2/CaF2 and Ag and oxidization of Ni3Al.
Key words:  laser cladding  metal matrix self–lubration coating  friction and wear  mechanism
手机扫一扫看